金钢石的制备研究

本文研究了两种不同质异构体石墨—金刚石的转化条件，以及在实验室现有条件下，利用石墨材料制备金刚石颗粒的具体方法和试验结果。     

Structural and magnetic properties of RF sputtered FePt/Fe multilayers

Series of [FePt(4min)/Fe(t_Fe)]₁₀ multilayers have been prepared by RF magnetron sputtering and post-annealing in order to optimize their magnetic properties by structural designs. The structure, surface morphology, composition and magnetic properties of the deposited films have been characterized by X-ray diffractometer (XRD), Rutherford backscattering (RBS), scanning electron microscope (SEM), energy dispersive X-ray spectroscope (EDX) and vibrating sample magnetometer (VSM). It is found that after annealing at temperatures above 500 °C, FePt phase undergoes a phase transition from disordered FCC to ordered FCT structure, and becomes a hard magnetic phase. X-ray diffraction studies on the series of [FePt/Fe]_n multilayer with varying Fe layer thickness annealed at 500 and 600 °C show that lattice constants change with Fe layer thickness and annealing temperature. Both lattice constants a and c are smaller than those of standard ones, and lattice constant a decreases as Fe layer deposition time increases. Only a slight increase in grain size was observed as Fe layer decreased in samples annealed at 500 °C. However, the increase in grain size is large in samples annealed at 600 °C. The coercivities of [FePt/Fe]_n multilayers decrease with Fe layer deposition time, and the energy product (BH)_max reaches a maximum in the samples with Fe layer deposition time of 3 min. Comparison of magnetic properties with structure showed an almost linear relationship between the lattice constant a and the coercivities of the FePt phase.     

Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007     

Surface and interfacial properties of PVDF/acrylic copolymer blends before and after UV exposure

Morphological and chemical properties of both the surface and interface of poly(vinylidene fluoride)/poly(methyl methacrylate)-co-poly(ethyl acrylate) (PVDF/PMMA-co-PEA) blend films have been investigated before and after the samples were exposed to ultraviolet (UV) irradiation using a xenon arc lamp at 50 °C and 9% relative humidity (RH) for 7 months. Surface and interfacial morphologies were studied by atomic force microscopy (AFM). Chemical composition information was obtained by confocal Raman microscopy, attenuated total reflection-FTIR spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. Results show an enrichment of the PVDF material at the air surface, while the acrylic copolymer enriches the interface. Blends having greater than 50% mass fraction of PVDF show little change in the surface morphology after UV exposure for 7 months. However, for a lower PVDF content, blends exhibit significant degradation of PMMA-co-PEA copolymer and a much rougher surface after UV exposure. Microstructural changes in the PVDF spherulites are also observed after UV degradation. It is found that the surface and interfacial morphologies are correlated with the chemical properties.     

PbWO4晶体空位型缺陷电子结构的研究

采用基于密度泛函理论的相对论性离散变分和嵌入团簇方法计算了PbWO4晶体中与氧空位和铅空位相关缺陷的态密度分布,并运用过渡态方法计算了其激发能.结果表明:PbWO4晶体中WO3+VO缺陷的O2p→W5d跃迁可引起350nm和420nm附近的吸收,并且发现VPb的存在可以使WO42基团的禁带宽度明显变小 关键词： PbWO4晶体 密度泛函 氧空位和铅空位 态密度分布     

Characteristics of transmission of electrons in a quantum wire tangentially attached to a superconductor ring threaded by magnetic flux

We present numerical investigations of the transmission properties of electrons in a normal quantum wire tangentially attached to a superconductor ring threaded by magnetic flux. A point scatterer with a δ -function potential is placed at node to model scattering effect. We find that the transmission characteristics of electrons in this structure strongly depend on the normal or superconducting state of the ring. The transmission probability as a function of the energy of incident electrons, in the case of a superconductor ring threaded by one quantum magnetic flux, emerges one deep dip, imposed upon the first broad bump in spectrum. This intrinsic conductance dip originates from the superconductor state of the ring. When increasing the magnetic flux from one quantum magnetic flux to two, the spectrum shifts toward higher energy region in the whole. This conductance dip accordingly shifts and appears in the second bump. In the presence of a point-scatterer at the node, the spectrum is substantially modified. Based on the condition of the formation of the standing wave functions in the ring and the broken of the time-reserve symmetry of Schr?dinger equation after switching magnetic flux, the characteristics of transmission of electrons in this structure can be well understood. Received 6 November 2001     

Facile preparation of new unsymmetrical curcumin derivatives by solid-phase synthesis strategy

Seventeen unsymmetrical curcumin derivatives were synthesized in good yield and purity by a facile solid phase synthesis strategy.     

Microwave absorption properties of composite powders with low density

The composites of barium ferrite coated on hollow ceramic microspheres were prepared using sol-gel technique. The crystal structure, morphology and microwave absorption properties of composite powders with different weight ratio of microspheres were studied with XRD, EDS, FESEM and vector network analyzer. The results show that the microwave absorption properties of composite powders are greatly improved. The maximum microwave loss of composite powders reaches 31 dB with an amount of 50 wt.% microspheres, and its density is only about 1.80 g/cm³. The effect of hollow ceramic microspheres on the microwave absorption property is also discussed.     

Propagation of elegant Laguerre–Gaussian beams through an annular apertured paraxial ABCD optical system

Based on the generalized Huygens–Fresnel diffraction integral and the expansion of the hard aperture function into a finite sum of complex Gaussian functions, the approximate analytical expression of elegant Laguerre–Gaussian beams passing through a paraxial ABCD optical system with an annular aperture is derived. Meanwhile, the corresponding closed-forms for the unapertured, circular apertured or circular black screen cases are also given. The obtained results provide more convenience for studying their propagation and transformation than the usual way by using diffraction integral formula directly. Some numerical examples are given to illustrate the propagation properties of elegant Laguerre–Gaussian beams.